What size are water heater supply lines?
“Most homes will need 3/4”. Some of the older houses in town, though, piped the entire hot water system in 1/2”, to get the hot water faster and cut down on waste.”
Can I use flexible pipe for water heater?
You can use flexible gas tubes or water pipes for a gas water heater in most states. In states with earthquakes, they can even be mandatory. If your existing gas pipe has CSST (corroded stainless steel tubes) or has not been glued, the connection should be replaced right away.
Does electric water heater need 18 inches off the ground?
When installing your heater 18 inches off of the ground, it’s important to remember that the stand between your heater and the ground should be strong enough to hold up a full tank, not just an empty one. While the 18-inch rule is part of the Uniform Plumbing Code, regulations can change from city to city.
Can you use 1/2 pipe water heater?
Yes, you can in most cases. Water heaters have 3/4″ connections to allow for increased flow and pressure where it’s needed and where the pipes are larger, but that doesn’t mean your plumbing has to match. The heater will flow at the same rate (more or less) as a straight run of 1/2″ pipe in your case.
What size should a water supply line be?
In most cases, the main pipeline from the street to your home is either 3/4 or 1 inch in diameter, supply branches use 3/4-inch-diameter pipe, and pipes for individual components are 1/2 inch. Remember that water pressure decreases by a half-pound per square inch for every foot pipes extend above your water supply.
Can you use PEX tubing on hot water heater?
PEX tubing may be connected directly to residential electric tank or tankless (instantaneous) water heaters, if the local code and manufacturer’s instructions allow. When connecting PEX tube to gas tank or tankless water heaters, the tube must be kept at least 6 inches away from the exhaust vent of the heater.
Does an electric water heater have to be elevated?
It is not necessary for electric water heaters, or 30 to 50-gallon gas water heaters manufactured after mid-2003. The code states that “appliances having an ignition source shall be elevated not less than 18 inches (457 mm) above the floor in garages,” and the purpose of this stipulation is fire safety.
What type of pipe is used for water heaters?
CPVC pipes are an ideal choice for hot water plumbing. They are made after adding material that goes through extra chlorination process which gives CPVC higher quality.
Can I use SharkBite on water heater?
SharkBite hot water heater connections are approved for use on electric or gas water heaters with a flu vent.
Whats better 1 2 or 3 4 water line?
Running 3/4″ piping from the 1/2″ feed will slightly decrease the pressure loss, meaning you’ll get more pressure at your fixtures, but the difference will probably be very small. Most of the pressure loss will have already occurred in the 1/2″ line before it reaches your house.
Can you use SharkBite fittings on hot water heater?
Yes, you can use SharkBite fittings on hot water lines. Remember, however, that they only work with copper, PEX, and CPVC pipes.
Can Blue PEX pipe be used for hot water?
Color-Coded: Red PEX pipes can be used for hot water supply lines, blue PEX for cold water supply, and white for either hot or cold.
When should you not use PEX pipe?
PEX plumbing is fine inside the walls of a home, no matter the temperatures as it can be covered with insulation. However, one of the disadvantages of PEX plumbing is it cannot be used outdoors in cold climates as there is no way to cover them and protect them from freezing temperatures.
Does an electric water heater need to be elevated?
Does an electric water heater need to be level?
New water heaters or water heaters that are placed on an un-level surface, need to be leveled and shimmed for them to work properly. All real estate properties must be equipped with a hot water heater, and damaged ones need to be replaced before the property is considered marketable.