How do I reset my ADSL line?

How do I reset my ADSL line?

  1. Open up a web browser and type in the IP address of the ADSL Router (default is 192.168. 1.1). Press Enter.
  2. Enter the Login name and password (default is admin/admin).
  3. Click on the Tools tab at the top.
  4. Click on the Restore button to factory reset on the unit.

How do I reset my DSL port?

Performing a Line Sync or Port Reset

  1. Remove the power cable from your ADSL modem.
  2. Unplug your ADSL modem from the phone socket at the wall.
  3. Disconnect any telephones or fax machines also connected to the line (this step is optional, but recommended)
  4. Wait 12 minutes (make sure you use a timer)

How do I reset my Telkom ADSL port?

Login to your account. Navigate to your Active Services. You will notice the Port reset feature button next to the broadband product in question. Hit the button and watch the magic.

How do you reset a port?

How to reset COM ports?

  1. Click Start – write regedit then click Enter.
  2. Navigate through folders: HKEY_LOCAL_MACHINE\SYSTEM\CurrentConstrolSet\Control\COM Name Arbiter.
  3. Double-click right click ComDB on right panel.
  4. This will open a window with addresses ports. To reset, enter all zeros, as shown below:

How do I open ports on my Telkom router?

The basic process to open a port is:

  1. Setup a static IP address on either your computer or device that you want to forward a port to.
  2. Login to your Telkom ADSL 5102G router.
  3. Navigate to the port forwarding section. Click the Advanced Setup link. Click the NAT link.
  4. Create a port forward entry.

How do I know if my DSL port is working?

Go to the “WAN,” “Status” or “Connection” page. Write down the values listed in the Signal Attenuation section. If the attenuation shows 20db or lower, your DSL line is performing extremely well; a range between 20 to 40db indicates a good signal; and anything higher than 40db may indicate a bad connection or wiring.

Why do I have to reset my modem every day?

The need to keep resetting your cable modem is because of problems with it. If you leave the connections that send data to the modem open for long, it consumes its memory, making the modem run into bugs, which slows it down. Also, its operating system may freeze, hence the need to keep on resetting.

What happens when modem is reset?

A reset restores your modem to its factory default settings. It will also erase any customized settings you may have changed, including static IP address setup, DNS, personalized password, WiFi settings, routing and DHCP settings.

Does Telkom allow port forwarding?

Setup a static IP address on either your computer or device that you want to forward a port to. Login to your Telkom ADSL 5102G router. Navigate to the port forwarding section. Click the Advanced Setup link.

How do I activate my Telkom ADSL?

The ADSL Verify is for customers who have selected the ADSL modem self install option. Once you have completed the modem installation process, submit the form below and your ADSL account will be activated and operational. Should you require assistance, free access to the Telkom helpdesk is available.

How do I Reset ports on my Device?

To reset, enter all zeros, as shown below: Once you confirm the changes by clicking on OK, our ports are reset. We can also check: 1. Click Start – write devmgmt.msc or simply Device manager, then click Enter. 2. From the middle pane, expand Ports (COM & LPT), right-click on any of the available ports and Properties 3.

How do I Reset my ports in comdb?

Double-click right click ComDB on right panel 4. This will open a window with addresses ports. To reset, enter all zeros, as shown below: Once you confirm the changes by clicking on OK, our ports are reset. We can also check: 1. Click Start – write devmgmt.msc or simply Device manager, then click Enter. 2.

What port does Exchange Server use to receive mail?

On the Exchange Server, the inbound connector is set to listen on port 25 (server interface) and to receive mail from only 1 IP (remote server / SMARTHOST). The Group is set to allow only “anonymous users”. sending messages / incoming messages are delivered normaly, then they are deferred by Exchange.

What happens to COM port settings when restarting the system?

However, when you restart the system, you find that the setting reverts back to the default: In Microsoft Windows 2000, COM port settings for command functions are maintained only for the active Windows session.